E2130
Bosch · Dishwasher · Error Code

Bosch Dishwasher E2130 Error Code — Heating / Circulation System Electronics Fault

Reset First — Then Call Bosch Also shown as: E-2130 E 2130
Quick Answer

The E2130 error code appears on Bosch's newer HomeConnect and Series 8 dishwashers. Bosch's published guidance is precise and brief: reset power to the breaker for 30 seconds; if not resolved, call Bosch Customer Support at 1-800-944-2904. No component-level detail is published by Bosch on their consumer pages for this code. E2130 sits in the E21xx code family alongside E2120, which shares identical published guidance. The "E21" prefix on Bosch's newer platform most likely corresponds to faults in the heating/circulation system electronics — the same territory as E20 and E21 on older two-digit displays. A breaker reset is the only DIY step available and should always be done first.

Sibling
E2030
System electronics fault. Identical Bosch guidance: reset + call.
Sibling
E2120
Electronics fault. Identical Bosch guidance: reset + call.
This code
E2130
Heating/circulation electronics fault. Reset + call Bosch.
Time
30 sec–2 hrs
Difficulty
Easy (reset) / Hard (hardware)
DIY Step
Breaker reset only
DIY Cost
Free

What the E2130 Code Means

Bosch's official guidance for E2130: Reset power to breaker for 30 seconds. If not resolved, call Bosch Customer Support at 1-800-944-2904. Bosch publishes no component-level detail for this code on their consumer support pages.

E2130 is a fault code on Bosch's newer generation of dishwashers — those using the longer numeric code system introduced with HomeConnect and Series 8 / Series 6 models. Unlike many of the shorter codes (E09, E15, E25) where Bosch provides explicit component-level guidance, the E21xx family — which includes E2120 and E2130 — receives identical treatment from Bosch: a 30-second breaker reset is the published DIY step, followed by a call to customer support if that doesn't clear the code.

Based on the structure of Bosch's code numbering and the component families the E21xx group maps to, E2130 most likely indicates a fault in the heating or circulation system electronics — the same territory as E20 (circulation pump winding fault) and E21 (circulation pump mechanical blockage) on older two-digit display models. The "21" prefix is consistent with Bosch's newer platform mapping of heating/circulation faults into the 2100–2199 range. However, because Bosch has not published the specific sub-system detail for E2130 on their consumer pages, this interpretation should be treated as informed context rather than a definitive component-level diagnosis.

What is certain is that E2130 on your machine is telling you the control board has detected a fault in this system, that a power reset is the only published first-line step, and that the technician path begins with calling Bosch Customer Support. Do not attempt to disassemble the machine or replace components based solely on E2130 without a technician's diagnosis — the specific sub-fault within the heating/circulation electronics category needs to be confirmed before any part is ordered.

Most Likely Causes

1
Transient control board fault from a power event. A power outage, voltage surge, or tripped breaker mid-cycle can leave the board's heating/circulation monitoring circuit in a fault state, producing E2130 without any hardware damage. A breaker reset clears this at no cost — and Bosch's own guidance starts here. Common
2
Circulation pump winding or motor fault. The circulation pump motor has an electrical fault — a short or open break in the winding — that the control board's heating/circulation monitoring detects as a system anomaly and raises E2130. Symptoms alongside the code would include cycles stopping mid-wash with dishes unsprayed and no water circulation sound. Possible
3
Circulation pump mechanical blockage. A foreign object jammed in the circulation pump impeller prevents it from reaching the correct speed, producing a fault in the circulation system. Cycles may stop partway through with a brief grinding noise at the start of the wash phase. Possible
4
Heating element or thermistor fault feeding into the system. A failed heating element or temperature sensor can produce conditions the board's heating/circulation electronics interprets as an E2130-category fault. Dishes coming out cold and wet alongside the code point in this direction. Possible
5
Control board or power module electronics failure. The board's internal monitoring circuit for the heating/circulation system has suffered a hardware fault. Factory-programmed replacement boards are required for this platform — a technician-only repair. Confirmed fault — needs technician

What to Do — Step by Step

1

Reset the circuit breaker for at least 30 seconds

Trip the dishwasher's circuit breaker and leave it off for at least 30 seconds — Bosch's published guidance for E2130. A full 5 minutes is better, giving the control board's capacitors time to fully discharge and clear any transient fault state. Restore power and run a complete wash cycle while staying nearby.

If E2130 clears and the cycle completes normally — wash water heats, dishes come out clean and dry — a power event was the cause. Monitor over the next few days for recurrence.
2

Observe the cycle carefully for secondary symptoms

While the machine runs, listen for any grinding or buzzing sound at the start of the wash phase (suggests a jammed circulation pump impeller — E21-type fault). Notice whether you can hear water circulating through the spray arms. Check whether dishes feel warm when the door is opened at cycle end. These observations help narrow the fault for the technician, saving diagnostic time and cost.

3

Clean the filter as a precaution

A severely clogged filter adds resistance throughout the wash system and can stress the circulation pump enough to contribute to fault conditions. With the machine off, remove and rinse all three filter components — the cylindrical mesh filter, flat coarse filter, and fine mesh floor panel — under warm running water. This is quick, free, and eliminates the filter as a contributing factor.

4

If E2130 returns — call Bosch Customer Support

This is Bosch's own published next step. Have your model number ready before calling (found on the label inside the door frame or the kick plate). Bosch Customer Support can look up the specific sub-fault mapped to E2130 for your exact model and generation, and can book a certified technician if needed. Call 1-800-944-2904.

Check your warranty first. If your dishwasher is less than one year old, E2130 on a new machine with no prior issues is almost certainly a warranty repair. Have your purchase receipt ready.

When to Call a Technician

A breaker reset is the only published DIY step for E2130. Call a technician if:

  • E2130 returns after a full 5-minute breaker reset
  • The cycle stops mid-wash with no sound of water circulating — possible circulation pump fault
  • A brief grinding or buzzing sound precedes E2130 at the start of a wash phase — possible jammed pump impeller
  • Dishes come out cold and wet despite the cycle completing — possible heating element fault
  • The machine refuses to start at all after E2130 appears — possible board-level lockout
  • E2130 appears on a machine still under warranty — this is a warranty repair; contact Bosch before booking a third-party technician

Repair Cost Expectations

If the Reset Fixes It

Free
A breaker reset costs nothing and resolves E2130 in cases where a power event was the cause — a meaningful share of first-occurrence reports.

Professional Repair

$180–$500
Typical range in the Boston area depending on confirmed fault: circulation pump clearing or replacement ($180–$300), heating element or thermistor ($140–$280), or control board replacement ($300–$500), parts and labor included.

Related Bosch Dishwasher Codes

E20
Circulation pump winding fault (older models)
E21
Circulation pump blocked (older models)
E09
Heating element fault — no heat
E07
Drying fan / E2030 system fault
View all Bosch dishwasher error codes →

Getting E2130 and the Reset Didn't Help? We'll Diagnose It.

Same-day appointments across Boston. Certified Bosch technicians with access to factory service data for current-generation models, and a 90-day warranty on every repair.

Book Bosch Dishwasher Repair Call (781) 666-9565

Frequently Asked Questions

What does E2130 mean on a Bosch dishwasher?

E2130 is a fault code on Bosch's newer HomeConnect and Series 8 dishwashers indicating a fault in the heating or circulation system electronics. Bosch's official consumer guidance for E2130 is to reset the breaker for 30 seconds and call 1-800-944-2904 if the code persists — no component-level detail is published on their consumer pages. Based on Bosch's code numbering structure, E2130 likely maps to a heating/circulation system fault, the same territory as E20 and E21 on older displays.

Is E2130 the same as E21 on older Bosch models?

They are related but not identical. E21 on older two-digit displays specifically indicates a mechanical blockage in the circulation pump impeller — a fault that produces a brief grinding sound and can sometimes be resolved by clearing debris from the pump. E2130 on newer models points to the broader heating/circulation electronics category, which includes but is not limited to the circulation pump. Because Bosch hasn't published the specific sub-fault for E2130 on their consumer pages, a technician with access to the service bulletin for your model generation is needed to confirm the exact cause.

Why won't Bosch tell me what E2130 means in more detail?

Bosch's consumer-facing support pages publish repair guidance at the level that a typical homeowner can act on safely. For codes where the only actionable step is a breaker reset — because the remaining repairs involve mains-voltage components, factory-programmed control boards, or internal disassembly — Bosch routes the conversation to their Customer Support line rather than providing step-by-step DIY guidance that could lead to unsafe or ineffective repairs. This is the same approach they take for E6101, E3000, and several other newer-platform codes.

Can a power surge cause E2130 without anything being broken?

Yes — this is the most common cause of a first-occurrence E2130 that clears after a breaker reset. A voltage surge or power outage mid-cycle can leave the control board's heating/circulation monitoring circuit in a fault state, displaying E2130 even when all hardware is intact. The breaker reset discharges the board fully and allows it to start fresh. If E2130 returns on the next cycle after a proper reset, a hardware component has failed.

How much does it cost to fix E2130?

A breaker reset costs nothing. If a technician is required — which Bosch directs users toward if the reset doesn't help — the cost depends on the confirmed fault: circulation pump clearing or replacement typically runs $180–$300; heating element or thermistor replacement runs $140–$280; control board replacement runs $300–$500. All prices are for the Boston area, parts and labor included. If the dishwasher is still under warranty, the repair should be covered — contact Bosch before booking a third-party technician.